Navigate
or
Contact Us
Subscribe Download PDF

Printer driver and calibration steps for most Wasp Printers

Internal User
2024-12-12
in Manuals and Driver

Windows print driver for WPL Label Printers (see below for full list of models). This driver is compatible with 32-bit and 64-bit versions of Windows 11, 10, 8, 7, Vista, XP, and Windows Server 2003, 2008, 2012, 2016. 2019

Click on the link below or copy the link to your web browser:

https://dl.waspbarcode.com/kb/printer/WaspPrintDriver2024.2.exe

NOTE: If this is a new computer and you have McAfee Live Safe installed, pause real time scan for at least 15 minutes to install the printer as McAfee will block the installation process.

Installing the printer

  1. Turn on the printer, wait for the status light to display green, then plug its USB cable into the PC. After Windows installs its USB Printing Support driver (seen in Devices and Printers under Unspecified), the printer is ready for driver installation.
  2. Run the downloaded file, which extracts the drivers and runs the DriverWizard. You will see references to Seagull Scientific, Inc., which is normal. Follow the prompts to upgrade an older driver, or install a new driver.
  3. If there is an older version of the driver installed, the DriverWizard can upgrade in place. Reboot the PC if prompted. After you log back in, it may prompt to reboot again; please do so. When you log in again, it should confirm removal of the old driver(s).

Calibrating the printer

After installing your printer it will need to be calibrated to the size of the labels. Follow the steps below to calibrate:

1. Download the Diag Tool from the link below then unzip the file:
https://dl.waspbarcode.com/kb/printer/DiagTool_v1.63.zip

2. Once you have unzipped the file, run the Diag Tool.

1597159665767.png

3. Click on the Get button in the bottom right corner. Don’t worry about the information that populates the boxes. If you are calibrating a network printer, change the interface box to Ethernet

1677245548803.png

3a (Network) Click on Setup, you should see your printer listed. If not, click on Discover Device, if it's listed click on it to highlight, then exit.

1677245650655.png


1597159697793.png



4.  Click on the Calibrate Sensor button on the left.

1597159773677.png


5. Click on the first Calibrate button at the bottom left:

1597159793110.png

6. It should feed out 2 to 3 labels.  Click on Get again.  This time Look at Paper Width.  By default it will be 4.00. Change this to match your label size.

1597159825680.png

7. Change this to match your label

1597159887896.png

8. Click on Set in the bottom right.

1597159932275.png

9. Click on Print Test Page on the left. It should print correctly on only a single label.

1597159965818.png


Changing driver settings

Once it has been calibrated you will need to set your driver size.  

1. Open the Control Panel on your computer.  (Do not use Windows Settings as this does not allow you to change the printer’s default settings.)

1597160023188.png

1597160047755.png

1597160058522.png

2. Find your printer and right click on the printer and choose Printer Properties (4th on the list)


1597160086564.png

3. Click on the Advanced tab at the top of the screen

1597160112347.png

4. Click on Printing Defaults at the bottom of the screen

1597160134928.png

5. The first tab is Page Setup.  Stock, the default is 4” x 6”  click on the drop down box to change your label size.


1597160153672.png


1597160164590.png

6. Once you have selected your label size click Apply, then OK.  Click on the General tab and then click on Preferences.  

1597160186579.png

7. Make sure your label size is correct

1597160206476.png

If it’s not correct, change it to the correct size and click Apply then OK.  Once you click OK it will take you back to the General tab.  Click on Print Test Page.  It should print one label.

==============================================================================

Below is the full list of printers supported by this driver (sorted by number). All entries are for the standard 203 DPI print head, unless otherwise specified.

WPL4MB

WPL4ML

WHC25

WPL25

WPL-204

WPL-205

WPL206M, WPL206U

WPL-303

WPL304

WPL-305 (includes WPL305E)

WPL308

WPL308-300 (300 DPI print head)

WPL308-600 (600 DPI print head)

WPL406

WPL408

WPL-604

WPL-606

WPL-608

WPL-608-300 (300 DPI print head)

WPL-610

WPL-610-300 (300 DPI print head)

WPL612

WPL612-300 (300 DPI print head)

WPL612-600 (600 DPI print head)

WPL614

WPL614-300 (300 DPI print head)

WPL614-600 (600 DPI print head)

WPL614M

WPL618

WPL618-300 (300 DPI print head)

WPL618-600 (600 DPI print head)

WPL-644 (600 DPI print head for WPL608, WPL610, WPL612)

Related Pages